Quick Reference:

ERROR CODES 01 - 02 - 03 - 04 - 05 - 06 - 07 - 08 - 09 - 0A - 10 - 11 - 12 - 13 - 14 - 20 - 21 - 22 - 90 - 91 - 92 - 93 - 94 - 96 - 97 - 98

 

Code
Error Message
Description
Detection

01

REEL TROUBLE-1 The slack of the tape is detected during threading or unthreading, and then tape protection is done. Detected when the ratio of the FG frequency at a supply reel, take-up reel and threading motor is less than the specified value.
02
REEL TROUBLE-2 The slack or breaking of the tape is detected in search, fast forward, or rewind mode, and then tape protection is done. Detected when the ratio of the FG frequency at a supply reel and take-up reel is less than the specified value.
03
REEL TROUBLE-3 The slack or breaking of the tape is detected in playback mode, or either of the lock of the supply or take-up reel is detected, and then tape protection is done. Detected when the FG frequency at a supply or take-up reel is zero (0), or when the tension detected from a tension sensor is less than 15g
04
REEL TROUBLE-4 It is detected that the tape does not run at the speed of designation in fast forward or rewind mode, and then tape protection is done. Depends on the comparison between the tape speed using the FG frequency at supply and take-up reels and the designated speed.
05
REEL TROUBLE-5 It is detected that the supply or take-up reel cannot stop with a cassette is not inserted, or detected that over current has been flowing to supply and take-up reels. Detected using the FG frequency or current at supply and/or take-up reels.
06
TAPE TENSION ERROR When excessive tension is detected, tape protection is done. Detected when the tension detected from a tension sensor is more than 55g.
07
CAPSTAN TROUBLE It is detected that the tape does not run at the speed of designation in play or search modem and tape protection is done. Detected at the tape speed detected from the FG frequency at a capstan motor.
08
DRUM TROUBLE It is detected that drum motor rotation I not normal, and then tape protection is done. Detected when the drum speed obtained from the speed FG of the drum motor is less than the specified value.
09
TH/UNTH MOTOR TIME OUT It is detected that threading or unthreading is not completed, and then tape protection is done. Detected when threading or unthreading is not completed within ten second after it is started.
0A
THREADING TROUBLE It is detected that threading cannot be done, and then tape protection is done. Detected when the tape top sensor is acted during threading after the short FF mode is automatically entered three times.
10
HUMID Condensation is detected. Detected using a DEW (condensation) sensor.
11
TAPE TOP/END SENSOR TROUBLE The tape top or end sensor operation is defective. Detected when the tape top and end are detected at the same time.
12
TAPE TOP SENSOR TROUBLE The tape top sensor operation is defective. Detected when the tape top continues for more than seven seconds.
13
TAPE END SENSOR TROUBLE The tape end sensor operation is defective. Detected when the tape end continues for more than seven seconds.
14
FAN MOTOR TROUBLE The operation of the fan motor is defective. Detected according to the period of a ripple noise at the fan motor terminal.
20
CASSETTE COMPARTMENT MOTOR LOCK It is detected that cassette up/down operation is not completed, and then tape protection is done. Detected when cassette up/down operation is not completed within four seconds after it is started.
21
REEL SHIFT MOTOR LOCK It is detected that driving of the L position to S position or the S position to L position in the reel table is not completed, and then tape protection operation is done. Detected when reel table driving is not completed within four seconds after it is started.
22
REEL POSITION SENSOR TROUBLE The operation of the L/S position sensor of the reel table is defective. Detected when the L and S positions are detected at the same time.
90
KEY BOARD INTERFACE ERROR The interface between the KY-231 board and SS-52 board is defective. Detected when no interface signal is sent form the SS-52 board to the KY-231 board.
91
½ VD NOT EXIST No ½ VD signal input to SS-52 board is detected. Detected when no ½ VD signal input to the SS-52 board.
92
INTERNAL INTERFACE ERROR
The serial or parallele interface between below board and SS-52 board is defective. (DPR-36 board; parallele interface) Detected when no interface signal is sent form the each board to the SS-52 board three times continuously.

Sub error message

FP

FP: IC6 of FP-58 board

APR

APR: IC51 APR-1 board

RM

RM: IC2 of RM-130 board(BKDW-509)

SWC

SWC: IC2 of SWC-19 board

DPR

DPR: DPR-36 board

VPR

VPR: IC753 of VPR-1 board

TBC

TBC: IC202 of TBC-23 board (DVW-A500P/A500 only)

DM

DM: IC-906 if DM-89 board (DVW-A500P/A500 only)

93
CPU INITIALIZE ERROR The interface between below CPU on SS-52 board and main CPU (of IC5 on SS-52 board) is defective when the POWER switch is turned ON. Detected when no interface signal is sent form the each CPU to the main CPU at the POWER switch is turned ON.

Sub error message

DT

DT : IC2104

Main servo(SV1)

Main servo (SV1) : IC750

Drum servo(SV2)

Drum servo (SV2) : IC700

94
CPU INITIALIZE ERROR 2 The operational defect of main CPU (of IC5 on SS-52 board) is defective when the POWER switch is turned ON. (Not display on the video monitor) Detected when no interface signal is sent form the main CPU to the sub CPU (of IC50 on SS-52 board) at the POWER switch is turned ON.
96
NV-RAM Trouble The operational defect of the NV-RAM (setup menu data) on the SWC-19 board or SS-52 board is detected. Then, reset the data in the NV-RAM to the condition at exfactory for menu-1, 2, 3, and id code.  

Sub error message

menu-1 8

Menu-1 : IC13 of SS-52 board: See Note 2 Detected by the NV-RAM data's checksum. 

menu-2

Menu-2 : IC13 of SS-52 board: See Note 2

menu-3

Menu-3 : IC13 of SS-52 board: See Note 2

ID code

ID code : IC3, 4, 5 of SWC-19 board Detected by the NV-FAM data's checksum. 

SWC-1

SWC-1 : IC3 of SWC-19 board Detected when no interface signal is sent from the each NV-RAM to IC2 on the SWC-19 board.

SWC-2

SWC-2 : IC4 of SWC-19 board

SWC-3

SWC-3 : IC5 of SWC-19 board

SWC-4

SWC-4 : IC6 of SWC-19 board
97
SV NV-RAM TROUBLE The operation defect of the NV-RAM (servo adjustment data) on the DR-200 board is detected. Detected by the NV-RAM data's checksum.
98*1
NV-RAM TROUBLE The operational defect of the NV-RAM (IC6) (RF adjustment data or REMOTE-2 setup data) on the SWC-19 board is detected. Then, reset the data in the NV-RAM to the condition at factory. Detected by the NV-RAM data's checksum.

Sub error message

RF ADJUST DATA LOST

REMOTE-2 DATA RESET

Note 1: This error code is applied to the unit in which the version numbers of both SYS1 ROM (IC12) and SYS2 ROM (IC54) on the SS-52 board are 3.10 or higher.
Note 2: This description is applied to the unit in which the version numbers of both SYS1 ROM (IC12) and SYS2 ROM (IC54) on the SS-52 board are 3.10 or higher.

For the inapplicable unit, are as follows:

Menu-1 : IC3 of SWC-19 board

Menu-2 : IC4 of SWC-19 board

Menu-3 : IC5 of SWC-19 board